Follow Slashdot blog updates by subscribing to our blog RSS feed

 



Forgot your password?
typodupeerror
×
Japan Space

Japan Releases AKATSUKI's Pictures of Venus (discovery.com) 44

astroengine writes: The Japanese space agency JAXA has released a confirmation that their Venus mission Akatsuki did indeed enter orbit at Venus on Dec. 7 (JST) — releasing unprocessed images of the Venusian atmosphere as it entered orbit. The spacecraft is currently in a highly-elliptical 13-day, 14-hour orbit around the planet, coming within 400 kilometers (248 miles) at its closest point and reaching 440,000 kilometers (243,400 miles) away at its farthest. This mission has just become the most unlikely success story of 2015 after "missing" its intended Venus orbit way back in 2010.
This discussion has been archived. No new comments can be posted.

Japan Releases AKATSUKI's Pictures of Venus

Comments Filter:
  • by Anonymous Coward

    Spelling matters.

  • Looks a lot like what I had to go through to save my Jool mission. Congrats guys.

  • by turkeydance ( 1266624 ) on Wednesday December 09, 2015 @08:37PM (#51092615)
    Akatsuki releases images of Venus...did Venus give her permission?
    • by Anonymous Coward
      Don't worry, her privacy is protected by the mosaic filter on her pubes as per Japanese law.
  • I never knew that Venus had a big seam running perfectly in the middle of it.

  • As for why... (Score:5, Informative)

    by Rei ( 128717 ) on Wednesday December 09, 2015 @08:54PM (#51092693) Homepage

    ... all of this trouble happened, the Planetary Society blog had a nice detailed writeup [planetary.org] a while back. The "short" of it? Akatsuki has a new type of primary thruster based on ceramics to withstand the heat rather than exotic materials like dicilicide-lined niobium as are normally used on these sorts of small hypergolic thrusters; they wanted to prove the new technology. You generally run thrusters a bit fuel-rich and inject it in such a manner as to try limit combustion near the chamber and nozzle walls to keep the temperature down. Well, the pressurant valve to the fuel tank didn't open all the way (they think it corroded) but the oxidizer pressure valve opened all the way. So the burn kept getting more and more oxidizer rich, meaning hotter chamber and nozzle walls way past the design limits, until they cracked and the nozzle simply flew off.

    The only reason they were able to salvage this was because another unusual choice they did: to save mass, they implemented a more complicated hydrazine (fuel) feed system, allowing them to use the same hydrazine suppy for the main engine as for the small monopropellant RCS thrusters (tiny, low-efficiency maneuvering thrusters). Because they did this, they were able to take the fuel that was planned for the main engine and route it instead to the RCS engines. While they're less efficient and much lower thrust, they had enough excess fuel to pull off the maneuver (after first making the craft lighter by dumping the now-unneeded oxidizer, of course!)

    • by Sowelu ( 713889 )

      Hoping I have this stuff right, please correct me if I'm wrong...
      If hydrazine is a monopropellant (energetically decomposes with a catalyst), and they used it for both RCS and their main thruster, then why was there oxidizer at all? Is it an efficiency thing where it burns better with oxygen, or am I missing something?

      • Re: (Score:2, Informative)

        by Anonymous Coward

        Hydrazine does burn hotter with oxidizer (thus faster exhaust gases, better efficiency), yes.

        (Incidentally, oxygen would not be the oxidizer of choice for a deep-space mission, since it will boil off -- dinitrogen tetroxide is the usual choice to go with hydrazine. Liquid at room temperature, with ignition on contact. Also horribly toxic.)

      • by Anonymous Coward

        Yes.
        Decomposing hydrazine as a monopropellant gets you ~185s specific impulse.
        Burning hydrazine with nitrogen tetroxide gets you ~245s.
        Note: that's rough figures for relatively low tech chamber and nozzle designs ca. 1970s. Modern materials and CFD optimized designs can likely get >20% higher.

    • by alantus ( 882150 ) on Wednesday December 09, 2015 @09:17PM (#51092801)

      In other words, they diverted power to the plasma manifolds.

    • Re:As for why... (Score:5, Informative)

      by Brett Buck ( 811747 ) on Wednesday December 09, 2015 @11:12PM (#51093175)

      Nice summary! I would note that the ability to interconnect the bipropellant hydrazine supply to the monopropellant engines is not an "unusual choice", it's common bordering on ubiquitous. Pretty much in order to provide this option as a backup.And it has been used in exactly this way (for more-or-less the same reason) in the very recent past.

      • Re:As for why... (Score:4, Informative)

        by Rei ( 128717 ) on Thursday December 10, 2015 @05:42AM (#51093955) Homepage

        I can think of a couple examples of spacecraft where it's been used that way (the Planetary Society's writeup mentions MESSENGER and MRO), but not many. Most of the designs I've seen use separate systems, for simplicity and supposedly extra reliability (the irony here being that the lack of separation on the systems is what saved Akatsuki). Cassini, for example has fully independent systems - like Akatsuki its main engine is hydrazine/N2O4 and its RCS is monoprop hydrazine, but the RCS has its own separate tank.

  • by ScentCone ( 795499 ) on Wednesday December 09, 2015 @10:10PM (#51092953)
    Why do the Japanese always choose December 7th to travel long distances and invade places?
  • Othewise Itachi will be pretty pissed.

Every nonzero finite dimensional inner product space has an orthonormal basis. It makes sense, when you don't think about it.

Working...