Slashdot Log In
Boeing's New 787 Wings — Amazingly Flexible
Posted by
ScuttleMonkey
on Wed Jun 27, 2007 02:27 PM
from the reed-in-the-wind dept.
from the reed-in-the-wind dept.
An anonymous reader writes "Boeing is making the wings of its new 787 out of carbon fiber instead of metal. That means the wings are so strong and flexible that they could bend upward and touch above the fuselage — or come close. The company is expected to deliver the first 787 to All Nippon Airlines in May 2008. 'Boeing has completed static testing of a three-quarter wingbox, but engineers are still considering whether to limit testing of the full wing to a 150% load limit held for 3 sec. or to continue bending it to see when it breaks. 'There's a raging debate within the engineering team to see if we should break it or not,' says [787 General Manager Mike] Bair.'" They have come a long way in wing flexibility.
Related Stories
[+]
Boeing Helping to Develop Algae-Powered Jet 326 comments
jon_cooper writes "Air New Zealand, Aquaflow Bionomic Corporation and Boeing are working together to develop and test a bio-fuel derived from algae. Aquaflow Bionomic Corporation began operating in May last year after it met a request from the local council to deal with excess algae on sewage ponds. Boeing's Dave Daggett was reported this year as saying algae ponds totaling 34,000 square kilometers could produce enough fuel to reduce the net CO2 footprint for all of aviation to zero."
[+]
Technology: Boeing 787 Dreamliner Delayed Again 214 comments
An anonymous reader writes "It's not just that the Boeing 787 Dreamliner may be unsafe or vulnerable to hacker attacks. At this point, it seems everyone would be happy for it to arrive in any state. The 787's carbon-fiber construction and next-generation technology have pushed back their delivery schedule once again, this time requiring a redesign of the plane's wingbox. Airlines will have to wait 18 more months to get it delivered, which is an extremely serious blow to the credibility of the company and their financial standing, as they would have to pay penalties to the buyers of more than 850 of these planes. And we thought Airbus had problems." Good thing Boeing can still count on its patent portfolio.
This discussion has been archived.
No new comments can be posted.
The Fine Print: The following comments are owned by whoever posted them. We are not responsible for them in any way.
Full
Abbreviated
Hidden
Loading... please wait.
missed the best part... (Score:4)
Re:missed the best part... (Score:5, Funny)
Parent
Ornithopter? (Score:4, Informative)
Parent
Re:missed the best part... (Score:5, Interesting)
Parent
YMCA (Score:5, Funny)
Parent
I hope they test it! (Score:5, Insightful)
No one's ever really tried that before, so testing is critical.
Since this seems like such a new concept (please correct me if I'm wrong; I don't follow plane technology too much), it would just seem prudent to try bending the wings until they break... how can they make accurate judgments and calculations without knowing exactly how much stress the wings can take before snapping?
Re:I hope they test it! (Score:4, Interesting)
You don't need to. You test to 150% of the rated load factor.
I think for for airliners it is +3 -2 Gs. It has been a few years since I needed to know it.
So you would test the wing to 4.5 Gs.
If it passes it is good to go.
Testing to destruction is good data to have but not required. If they get to to a 9 g load and the wing doesn't break I really think they could stop. Any airliner pulling a sustained 3 Gs will end up on the nightly news.
Parent
Re:I hope they test it! (Score:5, Informative)
Since you can not make the wing infinitely strong you you put operating limits in it.
One "neat" trick they use involves airspeed. When you start pulling Gs your stall speed goes up. Once a wing is stalled it stops generating lift so it unloads.
Back in the day your airspeed indicator had arcs. The green arc means that your wing will stall before it breaks.
The Yellow arc means that yes you can break the wing if you try.
The Red line means bad things are going to happen.
So when flying into storms the pilot can slow the the top of the green arc and be safe.
BTW a stall at altitude isn't a terrible thing. It is better than breaking the wing.
With this wing it may have an all Green arc.
As to breaking the structure to learn things. Yes but that kind of testing is expensive. If the wings of the 787 pass with a bigger than average margin then I would much rather see them do repetitive tests to see how it does with multiple over stress conditions.
The thing about some of the composites I have dealt with is some don't fail gracefully. I have parts of aircraft deform from stress but not totally fail. In other words it will get you home but she isn't going to fly again without A LOT of work.
I have seen carbon fiber get a good scratch in it and the next thing you know it is in a million part small parts.
Parent
Re:I hope they test it! (Score:5, Funny)
If this doesn't bring my karma down
Parent
Re:I hope they test it! (Score:5, Informative)
My doctorate is in Mechanical Engineering - Materials, in this case fracture mechanics. The fact that the wing is so strong suggests that it may be being over-designed. My graduate structures professor, who worked on the 747, point out that airplanes are designed for what might be called simultaneous mode failures -- there is no point in having the wings significantly stronger than the fuselage, as once the fuselage breaks the wings don't do you any good, you have just been carrying too much material in the wings. The same is true for all sub-systems. Hence, you have to do a very exhaustive analysis of the expected situations and make sure that all of them are appropriately covered, then you add a safety factor.
Typically, fatigue cracking has been the limiting factor in aircraft structures, and has caused numerous crashes. With the experience that has been gained in military programs, we should now know enough to use these composites properly.
Parent
Re:I hope they test it! (Score:5, Funny)
Parent
Re:I hope they test it! (Score:5, Insightful)
Parent
Re:I hope they test it! (Score:4, Informative)
Parent
Re:I hope they test it! (Score:5, Informative)
It sounds as if Boeing uses a "factor of safety" of 1.5, where the maximum anticipated load is multiplied by the factor of safety to determine the design strength of the wing. The factor of safety is calculated based on the earliest failure mode of the part, so it could simply be that other failure modes than wing deformation and buckling (as seen in the youtube video) are what determines the factor of safety with this new carbon fiber wing.
Parent
It's probably designed to different criteria (Score:5, Interesting)
The first time this was really driven home to me was in undergraduate school in '88. A classmate was working on a portable carbon-fiber bridge project for the Army. It had to support the weight of a main battle tank crossing it. In the full-scale test demo, the general overseeing the project commented that you'd get one and only one tank crew to cross the bridge. He felt that after the other tank crews saw how much the bridge flexed, there was no way they'd want to drive on it.
Parent
Re:I hope they test it! (Score:5, Informative)
Parent
Re:I hope they test it! (Score:4, Funny)
Parent
Re:I hope they test it! (Score:4, Informative)
Parent
Re:I hope they test it! (Score:5, Funny)
Pfffft. Real slashdotters only need a headline.
Parent
Re:I hope they test it! (Score:4, Funny)
I'm not used to all these new fangled additions to
Parent
Re:I hope they test it! (Score:5, Funny)
Does it run linux?
Imagine a Beowulf cluster of those!
In Soviet Russia, aeroplane wings break you!
etc, etc, etc.
Clearly, you must be new here.
Parent
Re:I hope they test it! (Score:5, Funny)
Parent
Re:I hope they test it! (Score:5, Informative)
Parent
Re:I hope they test it! (Score:5, Funny)
Parent
Re:I hope they test it! (Score:5, Informative)
of course their is a downside to most changes.
by deform, you mean yield [wikipedia.org] so, yes if you exceed the limit of carbon fibre you likely have snapped, where as aluminum, you have destroyed the structure of the frame. So if they both exceeded this limit at the same load, the aluminum may allow you to make it through one event.
For this to be obviously safer, you need:
1) the yield points would have to be very close.
2) it must be a single yield event (not repeated yield points, leading to a quick fatigue failure)
3) you must know the event occured so that you will replace the yieldied aluminium part, before the next event.
4) the yield event would still have to be in the yield strength of the aluminum, and not exceed it to the point of failure.
I think that is the issue, all of these are false. Carbon fibre has a much higher yield point, the aluminum wings constantly need inspected for fatigue cracks, and with each cycle they become closer to the point of failure.
With the carbon fibre, as the wing bends, it is probably designed to self limit the load. Since the aluminimum cannot survive the same amount of movement, it cannot self regulate (it bends, which makes it hot, which makes it softer, which makes it bend more which makes it hotter and softer,...)
of course it takes alott of energy to bend carbon fibre also, so it is releasing energy as heat as well. Granted aluminum is a much better heat conductor, so it would naturally transfer that heat better. But carbon fibre is known to stay stronger at high temperatures than aluminum.
Parent
Re:I hope they test it! (Score:5, Informative)
You are correct that microfine stress fractures are impossible to see in a pure carbon structure. To work around that, every object has a very fine fibreglass layer (070 or thinner) on the outside surface. When stress is applied, the fibreglass shows the stress marks and you can then visually see that something is wrong.
The biggest issue with C/f structures is design life. At the time when I was last working in the industry (mid 90's), they weren't even sure what the maximum life was. There was no data anywhere in the world. The sailplane factories were stating that 10K hours was the minimum and they would test after that (metal airframes were 30K hours before EoL). There were studies being done at Melbourne's RMIT (Australia). The last I heard there was they got to 17K hours before failure of one wing. Given the absurd number of hours a commercial airliner does compared to a sailplane, I would hope and expect that they have done some lifetime studies beyond that. I haven't yet seen any numbers from Boeing about expected airframe life for their pure composite structures.
Parent
Re:I hope they test it! (Score:5, Interesting)
Parent
Re:I hope they test it! (Score:5, Insightful)
So, while some failure modes might be worse than traditional aluminum wings, it's also likely to be better in others.
Then it becomes a matter of risk assessment and minimization. A good example would be seatbelts - there is the occasional accident where you'd be better off without the belt, but in the vast majority of accidents you're far better off with it on.
Parent
Re:I hope they test it! (Score:5, Funny)
Parent
Why (not)? (Score:5, Interesting)
Well... (Score:5, Interesting)
Unless otherwise specified, a factor of safety of 1.5 must be applied to the prescribed limit load which are considered external loads on the structure. When a loading condition is prescribed in terms of ultimate loads, a factor of safety need not be applied unless otherwise specified
The three second requirement comes out of paragraph 305(b):
(b) The structure must be able to support ultimate loads without failure for at least 3 seconds. However, when proof of strength is shown by dynamic tests simulating actual load conditions, the 3-second limit does not apply. Static tests conducted to ultimate load must include the ultimate deflections and ultimate deformation induced by the loading. When analytical methods are used to show compliance with the ultimate load strength requirements, it must be shown that--
(1) The effects of deformation are not significant;
(2) The deformations involved are fully accounted for in the analysis; or
(3) The methods and assumptions used are sufficient to cover the effects of these deformations.
If our intrepid engineers manage to test to 200% for 3 second, then somebody is going to come along and say, "let's see if we can make the wings lighter"
Good thing or bad thing?....depends upon your point of view I guess.
As it turns out, validating airframe structures with respect to FAA airworthiness requirements is kinda what I do for a living.
Parent
Re:Well... (Score:5, Informative)
What reasonable is, depends on which field you look at. The same standards do not apply to structural engineering (buildings), civil engineering (bridges, dams), aerospace engineering (aircraft), electrical power engineering (building wiring, electrical distribution systems), etc etc.
The FAA standards are, they set a specific limit load condition calculation for classes of aircraft (light aircraft are different from jet transports carrying people, etc). That's based on performance, operational usage, and the number of people typically carried. There are load cases for limit loads for gust loading (suddenly hitting a headwind when you're already pulling Gs), wind shear, emergency pull-ups, etc. A speed is established, called maneuvering speed, below which nothing you can do to the aircraft is credibly likely to ever cause the aircraft to exceed the limit loads.
Then, you add a 50% safety factor on top of those loads (failure load >= 150% of design limit load), and demonstrate to the FAA's satisfaction that the aircraft meets that ultimate load. For jet transports carrying people, the demonstration requires that you take it out to the 150% load limit and see if it breaks there.
Now, that ultimate load can be expected to cause permanent damage to the wings. Pretty much any aircraft exceeding the design limit load (100%) will get grounded, and anything approaching 150% is guaranteed to have damage. Since the test to 150% damages the test structure for any aluminum aircraft, the usual assumption is that it's a good idea to just keep testing past 150% until it breaks.
But you just need to prove that it meets the 150% for the FAA to be happy.
Designers try to make the failure point slightly, but not too much, past 150% of design limit load. Because adding weight is expensive (operations costs), and as others have mentioned it doesn't do any good for the wing to be stronger if the fuselage breaks first, etc. The loads are all balanced; it's inefficient for things to fail at different points.
These standards are reasonable, for transport aircraft. We know that because large jets are not falling out of the sky due to wing failures. I can't offhand think of the last one that wasn't due to some external cause (collision, etc). There closest incident recently was the American Airlines 587 crash in 2001 (http://en.wikipedia.org/wiki/American_Airlines_F
Parent
The 787 (Score:4, Funny)
If only one could find a 4ft diameter chrome exhaust tip...
Must resist onomatopoeic humor... (Score:5, Funny)
Slashdot Poll (Score:5, Funny)
1. Chicken out and don't break 'em
2. See how far they go and post it to YouTube
3. Orinthop mode! Pull 'em back and let 'em flap!
4. Cowboy Neal
Shopping for planes has never looked more fun (Score:4, Funny)
Boeing Client: No, thank you, I take them flexible, like my women.
While its great they are so flexible (Score:5, Insightful)
What? (Score:5, Informative)
If the aircraft is experiencing extreme conditions which are bending the wing excessively, then you _want_ to lose lift, rather than stress the wing and airframe more. Kind of like how sailors change to smaller sails during storms.
Parent
One year ago? How about twelve? (Score:5, Informative)
The linked video may have been uploded about a year ago, but it cites as its source a PBS production from 1995. (Which, incidentally, is discussing an entirely different airplane, the 777.)
Old News: Flexible wings on the Boeing B-47 (Score:5, Interesting)
Don't break it (Score:5, Insightful)
The story was about one of the earlier Boeing's, they had stressed the wing to like 10 times any theoretical force that could be possibly placed on it during a rather publicized testing of its strength. They test folks were all about trying to break it.
During the process of doing this an exec asked them what they were doing. "Breaking the wing" they replied.
The exec said No, stop the testing.
Why? the testers asked.
Because the headline won't read ,
"Boeing wing breaks at 40 times the stress encountered during possible flight conditions",
Instead it will read
"New wing of new Boeing Jet Breaks".
Please note Its been awhile since I heard that story, but I think the point is pretty clear.
747 Wing Flex (Score:4, Interesting)
This is your captain... (Score:5, Funny)
787 is a revolution in design and manufacturing (Score:5, Informative)
1) Yes, it's almost completely carbon fiber. This means that the plane can (and is) lighter, so it will be more fuel efficient. Also, it's easy to make complex curved shapes, so the wings and fuselage are slightly more aerodynamic. Because carbon fiber structures are so strong, the windows can be larger, and the plane can be pressurized to a lower altitude (it will be pressurized to 6000' instead of the typical 8000' of today's fleet). There is no corrosion, and little worry about fatigue in composites.
2) The plane is not built in Seattle, although that's where the final assembly takes place. All of the building takes place in multiple facilities around the globe, each producing parts to Boeing's plans. These parts will "snap together" in the Everett plant. The first 787 is being assembled right now, and will roll out on 7/8/7 (just over a week from now.) Apparently the left wing was off by 2 thousands of an inch or so, the right wing was absolutely perfect. Boeing converted three 747's to be gigantic cargo transporters to move all the parts from around the world to Everett.
3) The plane has almost completely electric, without the high-pressure pneumatic systems that older planes had. In particular, the AC systems are electric. This will be somewhat more efficient, and safer.
4) The plan for certification of the plane is borderline insane. The final assembly started a couple of weeks ago, and the plane will be rolled out in a week, the first flight will be in a couple of months, and the first delivery will be in Q2 2008. This is a tiny fraction of the time this process required on previous airplanes -- maybe 1/4 the time of the 777 and even less than that of the latest Airbus. This would be remarkable, even if the plane wasn't revolutionary in every other way, too!
5) Aviation Week and Space Technology visited the final assembly line recently, and were surprised to find that it was almost an empty building. That's not because they weren't ready -- that's because there are almost no tools needed to assemble the plane. They snap together the pieces, install the landing gear, and roll it down the building on its gear installing the various subassemblies. Boeing intends to assemble a plane every three days once they get going, a remarkable and unprecedented schedule.
Anyway -- there are so many revolutions in this airplane that I would have thought it was a scam if it was any other company than Boeing. It remains to be seen if they can meet their goals, but so far things are going remarkably according to the plan they laid out a few years ago.
Thad
Re:Nothing new (Score:5, Informative)
Parent
Re:Nothing new (Score:5, Informative)
Yeah, it kind of reminds me of when Airbus called Boeing's composite barrel design "old fashioned" [nwsource.com]!
Bearing in mind that nobody has produced such a design yet, including Airbus. Until Boeing did it a couple of weeks ago, that is.
The A350 was designed in direct response to the 787, which surprised Airbus in the amount of interest it received (they had at the time placed their bets on the now-troubled A380 program, which may never break even). Saying the 787 copied any of the A350's design or construction methods is getting it completely backwards.
Parent
Re:Nothing new (Score:5, Informative)
Parent
Re:I really don't see the big deal (Score:5, Informative)
Parent
Re:Design accommodations? (Score:5, Funny)
What? Give up slashdot? Never. I'll die first.
Parent
Re:Who cares if they bend (Score:5, Funny)
No, I think that the "pull" of gravity is mass times the acceleration due to gravity. When you "pull" on something, you are talking about the force, not the acceleration. Not only are you a pedantic ass, but you are also wrong.
Parent